1) Connectors shall connect to a chimney flue at a point not less than how high above the lowest portion of the interior of the chimney flue? (801.12)
2) A chimney lining system listed for use in chimneys with reduced clearances shall be listed per? (801.18.4 Exception)
3) Common venting systems for appliances located on more than one floor level shall be prohibited except where all of the appliances served by the common vent are located in rooms or spaces that are accessed only from the outdoors. The appliance enclosures shall not? (??)
4) A Type L vent shall terminate no less than 2 feet above the highest point of the roof penetration and not less than 2 feet higher than any portion of a building within what distance of the penetration? (802.5)
5) Where vents pass through attic space, the shield shall terminate not less than how far above the insulation materials? (802.8)
6) Manual dampers shall not be installed in connectors except in chimney connectors serving? (803.5)
7) Where two or more connectors enter a common vent or chimney, which connector shall enter at the highest level? (803.7)
8) 12 inch chimney connectors for a low-heat appliance shall be what thickness of galvanized steel? (803.9, T803.9)
9) Chimney or vent connectors shall be supported in an approved manner, and joints may be fastened with which of the following? (803.10.1)
10) The maximum horizontal length of a single-wall connector for a vent or a chimney shall be what percent of the height of the chimney or vent? (803.10.2)
11) Chimney connectors for domestic appliances shall not pass through walls of combustible construction to reach a chimney unless the concealed metal parts of the pass-through system shall resist corrosion up to what temperature? (803.10.4(3))
12) Connectors shall rise vertically to the chimney or vent with a minimum pitch equal to what percent slope? (803.10.5)
13) A labeled solid-insulated factor-built chimney section, for a domestic appliance, with 1 inch of insulation and with a diameter of 2 inches larger than the chimney connector shall be installed with a steel chimney connector having a minimum thickness of 23.6 mils, that requires the minimum clearance to combustible wall materials from the connector to be what distance? (T803.10.4)
14) Direct vent appliances using forced draft venting shall be located so that the minimum clearance between the vent terminal at the side of the house and from any openings through which combustion products enter a building is a minimum of? (804.2.1)
15) The termination of chimneys or vents equipped with power exhauster shall be located not less than what distance from lot lines? (804.3.3)
16) A horizontal termination of a mechanical draft vent system where located adjacent to walkways, shall be not less than how high above the level of the walkway? (804.3.4(1))
17) A horizontal termination of a mechanical draft vent system shall terminate not less than 4 feet below, 4 feet horizontally from or how many feet above any door or window? (804.3.4(1))
18) An appliance vented by natural draft shall not be connected into a vent, chimney or vent connector on the? (804.3.6)
19) Factory built chimneys shall be listed and labeled and shall be installed and terminated? (805.1)
20) An unvented gas log heater shall not be installed in a factor-built fireplace unless the fireplace has been? (903.3)
21) A gasketed fireplace door installed on a factory-built fireplaces shall be specifically listed and labeled in accordance with? (903.4)
22) Plume discharges from cooling towers shall be not less than how far above or how far away from any ventilation inlet to a building? (908.3)
23) Drains from a cooling tower shall be connected to an approved disposal via? (908.6)
24) Ducts shall never be attached to? (909.4)
25) Wall furnaces hall never be placed closer than how far from a corner? (910.2)
26) Wall furnaces shall be placed such that drapery will not be nearer than how far from any portion of the register of the furnace? (910.2)
27) The lowest portion of an unsealed floor furnace shall have not less than how much clearance from grade level? (910.4)
28) Floor furnaces sealed by the manufacturer to prevent entrance of water shall require an oAset from the grade by what distance? (910.4)
29) A timer, if provided to control the main burner operation of a sauna, shall have a maximum time of? (914.4.1)
30) Volume dampers in forced air furnaces shall not be placed in the air inlet to a furnace in a manner that will? (918.3)
31) Outdoor intake openings for a forced-air furnace shall be located not less than how far from contaminant sources where such sources are located within 10 feet from the opening? (918.5)
32) Oil fired unit heaters shall be tested in accordance with? (920.1)
33) Radiant heating panels installed on wood framing shall be fastened no closer than how far from a heating element? (927.3)
34) What is the maximum temperature allowed to be provided to potable hot water distribution systems from a water heater? (1,002.2.2)
35) Packaged electric boilers shall be listed and labeled in accordance with? (1,004.1)
36) The installation of boilers shall conform to? (1,004.2)
37) Working clearance shall be provided to allow access for repair for boilers. Passageways around all sides of boilers shall have an unobstructed width of not less than? (1,004.3)
38) Hight pressure steam boilers having a heating surface in excess of 1,000 square feet shall have a minimum clearance from the top of the boiler to the ceiling of at least? (T1,004.3.1)
39) High pressure safety and relief valves shall be vented to? (1,006.6)
40) Every hot water boiler or multiple boiler installation shall be required to have? (1,009.1)
41) Hot water boiler gauges shall be installed so that the midpoint of the water gauge glass indicator is at the? (1,010.2.1)
42) A refrigeration system where all refrigerant containing piping and fittings are isolated and there is a low probability that refrigerant leaked from a failed connection could enter an occupied area is? (1,003.3.1)
43) The refrigerant classification of R-123 is? (T1,103.1)
44) What quantity of R-500 refrigerant is allowed in a refrigeration system per 1,000 cubic feet of room space without invoking special machinery room requirements? (T1,103.1)
45) Which of the following has a refrigerant classification of B1? (T1,103.1)
46) What room volume is used in estimating the allowable refrigerant for a system in a convenient store? (1,104.4.1)
47) What is the maximum refrigerant allowed for sealed absorption systems in exit access paths within residential units? (T1,104.3.2)
48) The minimum required ventilation exhausting rate for a 1,000 square foot machinery room is? (1,105.6.3.1)
49) A 1,000 square foot refrigeration machinery room, which uses 25 pounds of refrigerant, shall have a minimum mechanical ventilation rate of? (1,105.6.3.2, 1,105.6.3.1, [0.5 * 1,000 + 1,000 * sqrt(25)])
50) The termination of a relief device from a refrigeration machinery room shall be not less than how far from any window opening? (1,105.7)